Jump to content

Shane W

Members
  • Posts

    5
  • Joined

  • Last visited

Everything posted by Shane W

  1. I would like to know how to assign a specific ringtone to the #2 port of the Sangoma FXO card. I have a Viking Doorbell that allows communication using the phone system. It works well but the end users have no way of knowing someone is at the front door or just a regular caller.
  2. I have a Snom-one ver. 2011-4.3.0.1030 (Linux) Sangoma 4.2.2-1 When someone calls in on the pots line (sangoma port 1. I get a 20 second delay before the caller can hear me. I can hear the incoming caller they cannot hear me. After 20-25 seconds it works. I have the incoming default extension to 72 or a ring hunt group of about 6 phones. I have re-ran the Sangoma setup and used the v4IP address vs. the localhost or 127.0.0.1 and I also changed the setting in the sangoma under the Call control -> Analog Config. -> Inbound Call - Handling info -> and changed it to ON_OUTBOUND-MEDIA-AVAILABLE. After that I calibrated the FXO channels and it worked for about 10 calls then it went back to it old self.
  3. Hello, I'm a newbie getting this configured a bit at a time I have the Sangoma card working fine, I can call in but all calls going out result in "You must dial a one or zero when dialing this number. My dialplan just has one entry 100 200 * calls to and from internal extensions work fine. I can route calls inbound but no outgoing at all. Thanks in advance
  4. That seemed to do it. I do not know why I didn't try that after the re-image. Thx a million.
  5. Hello, I'm new to this but I have read and searched for hours to find a resolutiion I'm trying to deploy the SNOM one Plus and I re-imaged to get a fresh start. That went fine everything looks good except when trying to configure Sangoma A200 card. The driver is loaded and hardware is active but I get error when trying to write config file because the superadmin does not have rights to modify it. After reboot I get WANPIPE error could not start and NetBoard Express will not start from console command or via http interface. Thanks below is log file dump. Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.0: irq 50, io base 0x00003080 Jan 30 23:57:00 snomONE kernel: usb usb2: configuration #1 chosen from 1 choice Jan 30 23:57:00 snomONE kernel: hub 2-0:1.0: USB hub found Jan 30 23:57:00 snomONE kernel: hub 2-0:1.0: 2 ports detected Jan 30 23:57:00 snomONE kernel: ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 19 (level, low) -> IRQ 193 Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.1: irq 193, io base 0x00003060 Jan 30 23:57:00 snomONE kernel: usb usb3: configuration #1 chosen from 1 choice Jan 30 23:57:00 snomONE kernel: hub 3-0:1.0: USB hub found Jan 30 23:57:00 snomONE kernel: hub 3-0:1.0: 2 ports detected Jan 30 23:57:00 snomONE kernel: ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185 Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.2: irq 185, io base 0x00003040 Jan 30 23:57:00 snomONE kernel: usb usb4: configuration #1 chosen from 1 choice Jan 30 23:57:00 snomONE kernel: hub 4-0:1.0: USB hub found Jan 30 23:57:00 snomONE kernel: hub 4-0:1.0: 2 ports detected Jan 30 23:57:00 snomONE kernel: ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 177 Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.3: UHCI Host Controller Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Jan 30 23:57:00 snomONE kernel: uhci_hcd 0000:00:1d.3: irq 177, io base 0x00003020 Jan 30 23:57:00 snomONE kernel: usb usb5: configuration #1 chosen from 1 choice Jan 30 23:57:00 snomONE kernel: hub 5-0:1.0: USB hub found Jan 30 23:57:00 snomONE kernel: hub 5-0:1.0: 2 ports detected Jan 30 23:57:00 snomONE kernel: SCSI subsystem initialized Jan 30 23:57:00 snomONE kernel: ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 185 Jan 30 23:57:00 snomONE kernel: ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] Jan 30 23:57:00 snomONE kernel: scsi0 : ata_piix Jan 30 23:57:00 snomONE kernel: scsi1 : ata_piix Jan 30 23:57:00 snomONE kernel: ata1: SATA max UDMA/133 cmd 0x30b8 ctl 0x30cc bmdma 0x30a0 irq 185 Jan 30 23:57:00 snomONE kernel: ata2: SATA max UDMA/133 cmd 0x30b0 ctl 0x30c8 bmdma 0x30a8 irq 185 Jan 30 23:57:00 snomONE kernel: ata1.00: ATA-7: INTEL SSDSA2M040G2GC, 2CV102HD, max UDMA/133 Jan 30 23:57:00 snomONE kernel: ata1.00: 78165360 sectors, multi 16: LBA48 NCQ (depth 0/32) Jan 30 23:57:00 snomONE kernel: ata1.00: configured for UDMA/133 Jan 30 23:57:00 snomONE kernel: Vendor: ATA Model: INTEL SSDSA2M040 Rev: 2CV1 Jan 30 23:57:00 snomONE kernel: Type: Direct-Access ANSI SCSI revision: 05 Jan 30 23:57:00 snomONE kernel: SCSI device sda: 78165360 512-byte hdwr sectors (40021 MB) Jan 30 23:57:00 snomONE kernel: sda: Write Protect is off Jan 30 23:57:00 snomONE kernel: SCSI device sda: drive cache: write back Jan 30 23:57:00 snomONE kernel: SCSI device sda: 78165360 512-byte hdwr sectors (40021 MB) Jan 30 23:57:00 snomONE kernel: sda: Write Protect is off Jan 30 23:57:00 snomONE kernel: SCSI device sda: drive cache: write back Jan 30 23:57:00 snomONE kernel: sda: sda1 sda2 Jan 30 23:57:00 snomONE kernel: sd 0:0:0:0: Attached scsi disk sda Jan 30 23:57:00 snomONE kernel: Initializing USB Mass Storage driver... Jan 30 23:57:00 snomONE kernel: usbcore: registered new driver usb-storage Jan 30 23:57:00 snomONE kernel: USB Mass Storage support registered. Jan 30 23:57:00 snomONE kernel: device-mapper: uevent: version 1.0.3 Jan 30 23:57:00 snomONE kernel: device-mapper: ioctl: 4.11.6-ioctl (2011-02-18) initialised: dm-devel@redhat.com Jan 30 23:57:00 snomONE kernel: device-mapper: dm-raid45: initialized v0.2594l Jan 30 23:57:00 snomONE kernel: EXT3-fs: INFO: recovery required on readonly filesystem. Jan 30 23:57:00 snomONE kernel: EXT3-fs: write access will be enabled during recovery. Jan 30 23:57:00 snomONE kernel: kjournald starting. Commit interval 5 seconds Jan 30 23:57:00 snomONE kernel: EXT3-fs: recovery complete. Jan 30 23:57:00 snomONE kernel: EXT3-fs: mounted filesystem with ordered data mode. Jan 30 23:57:00 snomONE kernel: SELinux: Disabled at runtime. Jan 30 23:57:00 snomONE kernel: type=1404 audit(1327967774.955:2): selinux=0 auid=4294967295 ses=4294967295 Jan 30 23:57:00 snomONE kernel: e1000e: Intel® PRO/1000 Network Driver - 1.3.10-k2 Jan 30 23:57:00 snomONE kernel: e1000e: Copyright© 1999 - 2011 Intel Corporation. Jan 30 23:57:00 snomONE kernel: ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 169 Jan 30 23:57:00 snomONE kernel: e1000e 0000:02:00.0: (unregistered net_device): Failed to initialize MSI-X interrupts. Falling back to MSI interrupts. Jan 30 23:57:00 snomONE kernel: e1000e 0000:02:00.0: Disabling ASPM L0s Jan 30 23:57:00 snomONE kernel: input: PC Speaker as /class/input/input1 Jan 30 23:57:00 snomONE kernel: e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:03:1d:09:1c:3d Jan 30 23:57:00 snomONE kernel: e1000e 0000:02:00.0: eth0: Intel® PRO/1000 Network Connection Jan 30 23:57:00 snomONE kernel: e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF Jan 30 23:57:00 snomONE kernel: ACPI: PCI Interrupt 0000:00:1f.3 -> GSI 19 (level, low) -> IRQ 193 Jan 30 23:57:00 snomONE kernel: r8169 Gigabit Ethernet driver 2.3LK-1-NAPI loaded Jan 30 23:57:00 snomONE kernel: ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 177 Jan 30 23:57:00 snomONE kernel: r8169 0000:01:00.0: unknown MAC, using family default Jan 30 23:57:00 snomONE kernel: eth1: RTL8168b/8111b at 0xf891e000, 70:71:bc:bc:08:3b, XID 0c200000 IRQ 66 Jan 30 23:57:00 snomONE kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 30 23:57:00 snomONE kernel: floppy0: no floppy controllers found Jan 30 23:57:00 snomONE kernel: work still pending Jan 30 23:57:00 snomONE kernel: lp: driver loaded but no devices found Jan 30 23:57:00 snomONE kernel: ACPI: Power Button (FF) [PWRF] Jan 30 23:57:00 snomONE kernel: ACPI: Sleep Button (CM) [sLPB] Jan 30 23:57:00 snomONE kernel: ACPI: Mapper loaded Jan 30 23:57:00 snomONE kernel: dell-wmi: No known WMI GUID found Jan 30 23:57:00 snomONE kernel: md: Autodetecting RAID arrays. Jan 30 23:57:00 snomONE kernel: md: autorun ... Jan 30 23:57:00 snomONE kernel: md: ... autorun DONE. Jan 30 23:57:00 snomONE kernel: device-mapper: multipath: version 1.0.6 loaded Jan 30 23:57:00 snomONE kernel: loop: loaded (max 8 devices) Jan 30 23:57:00 snomONE kernel: EXT3 FS on dm-0, internal journal Jan 30 23:57:00 snomONE kernel: kjournald starting. Commit interval 5 seconds Jan 30 23:57:00 snomONE kernel: EXT3 FS on sda1, internal journal Jan 30 23:57:00 snomONE kernel: EXT3-fs: mounted filesystem with ordered data mode. Jan 30 23:57:00 snomONE kernel: Adding 2064376k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2064376k Jan 30 23:57:00 snomONE kernel: IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com> Jan 30 23:57:00 snomONE kernel: Loading iSCSI transport class v2.0-871. Jan 30 23:57:00 snomONE kernel: 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> Jan 30 23:57:00 snomONE kernel: All bugs added by David S. Miller <davem@redhat.com> Jan 30 23:57:00 snomONE kernel: libcxgbi:libcxgbi_init_module: tag itt 0x1fff, 13 bits, age 0xf, 4 bits. Jan 30 23:57:00 snomONE kernel: libcxgbi:ddp_setup_host_page_size: system PAGE 4096, ddp idx 0. Jan 30 23:57:00 snomONE kernel: Chelsio T3 iSCSI Driver cxgb3i v2.0.0 (Jun. 2010) Jan 30 23:57:00 snomONE kernel: iscsi: registered transport (cxgb3i) Jan 30 23:57:00 snomONE kernel: NET: Registered protocol family 10 Jan 30 23:57:00 snomONE kernel: lo: Disabled Privacy Extensions Jan 30 23:57:00 snomONE kernel: IPv6 over IPv4 tunneling driver Jan 30 23:57:00 snomONE kernel: cnic: Broadcom NetXtreme II CNIC Driver cnic v2.2.13 (Jan 31, 2011) Jan 30 23:57:00 snomONE kernel: Broadcom NetXtreme II iSCSI Driver bnx2i v2.6.2.3 (Dec 31, 2010) Jan 30 23:57:00 snomONE kernel: iscsi: registered transport (bnx2i) Jan 30 23:57:00 snomONE kernel: iscsi: registered transport (tcp) Jan 30 23:57:00 snomONE kernel: iscsi: registered transport (iser) Jan 30 23:57:00 snomONE kernel: iscsi: registered transport (be2iscsi) Jan 30 23:57:00 snomONE kernel: 8021q: adding VLAN 0 to HW filter on device eth1 Jan 30 23:57:00 snomONE kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready Jan 30 23:57:00 snomONE kernel: e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None Jan 30 23:57:00 snomONE kernel: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready Jan 30 23:57:00 snomONE kernel: ACPI Exception (acpi_processor-0265): AE_NOT_FOUND, Evaluating _PSS [20060707] Jan 30 23:57:00 snomONE last message repeated 3 times Jan 30 23:57:01 snomONE rpc.statd[2461]: Version 1.0.9 Starting Jan 30 23:57:01 snomONE pcscd: pcscdaemon.c:507:main() pcsc-lite 1.4.4 daemon ready. Jan 30 23:57:01 snomONE pcscd: hotplug_libusb.c:402:HPEstablishUSBNotifications() Driver ifd-egate.bundle does not support IFD_GENERATE_HOTPLUG. Using active polling instead. Jan 30 23:57:01 snomONE pcscd: hotplug_libusb.c:411:HPEstablishUSBNotifications() Polling forced every 1 second(s) Jan 30 23:57:05 snomONE automount[2644]: lookup_read_master: lookup(nisplus): couldn't locate nis+ table auto.master Jan 30 23:57:05 snomONE dhcpd: Internet Systems Consortium DHCP Server V3.0.5-RedHat Jan 30 23:57:05 snomONE dhcpd: Copyright 2004-2006 Internet Systems Consortium. Jan 30 23:57:05 snomONE dhcpd: All rights reserved. Jan 30 23:57:05 snomONE dhcpd: For info, please visit http://www.isc.org/sw/dhcp/ Jan 30 23:57:05 snomONE dhcpd: Wrote 23 leases to leases file. Jan 30 23:57:05 snomONE dhcpd: Jan 30 23:57:05 snomONE dhcpd: No subnet declaration for eth1 (10.0.0.70). Jan 30 23:57:05 snomONE dhcpd: ** Ignoring requests on eth1. If this is not what Jan 30 23:57:05 snomONE dhcpd: you want, please write a subnet declaration Jan 30 23:57:05 snomONE dhcpd: in your dhcpd.conf file for the network segment Jan 30 23:57:05 snomONE dhcpd: to which interface eth1 is attached. ** Jan 30 23:57:05 snomONE dhcpd: Jan 30 23:57:05 snomONE dhcpd: Jan 30 23:57:05 snomONE dhcpd: Not configured to listen on any interfaces! Jan 30 23:57:05 snomONE dhcpd: Jan 30 23:57:05 snomONE dhcpd: If you did not get this software from ftp.isc.org, please Jan 30 23:57:05 snomONE dhcpd: get the latest from ftp.isc.org and install that before Jan 30 23:57:05 snomONE dhcpd: requesting help. Jan 30 23:57:05 snomONE dhcpd: Jan 30 23:57:05 snomONE dhcpd: If you did get this software from ftp.isc.org and have not Jan 30 23:57:05 snomONE dhcpd: yet read the README, please read it before requesting help. Jan 30 23:57:05 snomONE dhcpd: If you intend to request help from the dhcp-server@isc.org Jan 30 23:57:05 snomONE dhcpd: mailing list, please read the section on the README about Jan 30 23:57:05 snomONE dhcpd: submitting bug reports and requests for help. Jan 30 23:57:05 snomONE dhcpd: Jan 30 23:57:05 snomONE dhcpd: Please do not under any circumstances send requests for Jan 30 23:57:05 snomONE dhcpd: help directly to the authors of this software - please Jan 30 23:57:05 snomONE dhcpd: send them to the appropriate mailing list as described in Jan 30 23:57:05 snomONE dhcpd: the README file. Jan 30 23:57:05 snomONE dhcpd: Jan 30 23:57:05 snomONE dhcpd: exiting. Jan 30 23:57:05 snomONE gpm[2710]: *** info [startup.c(95)]: Jan 30 23:57:05 snomONE gpm[2710]: Started gpm successfully. Entered daemon mode. Jan 30 23:57:05 snomONE kernel: WANPIPE Hardware Support Module 3.5.20.7.0 © 1994-2010 Sangoma Technologies Inc Jan 30 23:57:05 snomONE kernel: usbcore: registered new driver sdlausb Jan 30 23:57:05 snomONE kernel: WANPIPE Interface Support Module 3.5.20.7.0 © 1994-2010 Sangoma Technologies Inc Jan 30 23:57:05 snomONE kernel: WANPIPE Multi-Protocol WAN Driver Module 3.5.20.7.0 © 1994-2010 Sangoma Technologies Inc Jan 30 23:57:05 snomONE kernel: wanpipe: Probing for WANPIPE hardware. Jan 30 23:57:05 snomONE kernel: ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 20 (level, low) -> IRQ 90 Jan 30 23:57:05 snomONE kernel: wanpipe: AFT-A200-SH PCI FXO/FXS card found (HDLC rev.13), cpu(s) 1, bus #5, slot #0, irq #10 Jan 30 23:57:05 snomONE kernel: wanpipe: Allocating maximum 1 devices: wanpipe1 - wanpipe1. Jan 30 23:57:05 snomONE kernel: WANPIPE: TDM Codecs Initialized Jan 30 23:57:05 snomONE kernel: WANPIPE WANEC Layer 3.5.20.7.0 © 1995-2006 Sangoma Technologies Inc. Jan 30 23:57:05 snomONE kernel: wanec_create_dev: Registering Wanpipe ECDEV Device! Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:098 [2819:2819] INFO - admin : Netborder Express Gateway version 4.1.4 Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:104 [2819:2819] INFO - netborder.infra.Application : Build : maint/nbe-4.1:21540? Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:574 [2819:2819] ERROR - netborder.pstn.config.XmlConfig : /opt/Netborder/Express/Gateway/config/pstn-config.xml:2: element pstnConfig: Relax-NG validity error : Element pstnConfig failed to validate attributes Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:574 [2819:2819] ERROR - netborder.pstn.config.XmlConfig : /opt/Netborder/Express/Gateway/config/pstn-config.xml:163: element boards: Relax-NG validity error : Expecting an element , got nothing Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:579 [2819:2819] ERROR - netborder.pstn.config.XmlConfig : failed to validate PSTN configuration file /opt/Netborder/Express/Gateway/config/pstn-config.xml against schema /opt/Netborder/Express/Gateway/config/pstn-config.rng Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:580 [2819:2819] ERROR - netborder.media.hostmedia.ToneBankManager : Can't load Pstn Config. Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:580 [2819:2819] ERROR - netborder.media.rtp.JRtpMediaEngine : failed to initialize tone bank manager Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:581 [2819:2819] ERROR - netborder.infra.DynlibObjectFactory : Error calling creation method "LoadMethod" Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:581 [2819:2819] ERROR - netborder.voip.DsVoipGatewayNetIf : Failed to get SIP Media Engine from library netborder-JRtpMediaEngine Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:581 [2819:2819] ERROR - netborder.voip.DsVoipGatewayNetIf : failed to configure sip network interface Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:582 [2819:2819] ERROR - netborder.infra.DynlibObjectFactory : Error calling creation method "LoadMethod" Jan 30 23:57:09 snomONE netborder: 2012-01-30 23:57:09:582 [2819:2819] ERROR - netborder.infra.Application : failed to load the VoIP library Jan 30 23:57:10 snomONE avahi-daemon[2860]: Found user 'avahi' (UID 70) and group 'avahi' (GID 70). Jan 30 23:57:10 snomONE avahi-daemon[2860]: Successfully dropped root privileges. Jan 30 23:57:10 snomONE avahi-daemon[2860]: avahi-daemon 0.6.16 starting up. Jan 30 23:57:10 snomONE avahi-daemon[2860]: WARNING: No NSS support for mDNS detected, consider installing nss-mdns! Jan 30 23:57:10 snomONE avahi-daemon[2860]: Successfully called chroot(). Jan 30 23:57:10 snomONE avahi-daemon[2860]: Successfully dropped remaining capabilities. Jan 30 23:57:10 snomONE avahi-daemon[2860]: No service found in /etc/avahi/services. Jan 30 23:57:10 snomONE avahi-daemon[2860]: New relevant interface eth1.IPv6 for mDNS. Jan 30 23:57:10 snomONE avahi-daemon[2860]: Joining mDNS multicast group on interface eth1.IPv6 with address fe80::203:1dff:fe09:1c3d. Jan 30 23:57:10 snomONE avahi-daemon[2860]: New relevant interface eth1.IPv4 for mDNS. Jan 30 23:57:10 snomONE avahi-daemon[2860]: Joining mDNS multicast group on interface eth1.IPv4 with address 10.0.0.70. Jan 30 23:57:10 snomONE avahi-daemon[2860]: Network interface enumeration completed. Jan 30 23:57:10 snomONE avahi-daemon[2860]: Registering new address record for fe80::203:1dff:fe09:1c3d on eth1. Jan 30 23:57:10 snomONE avahi-daemon[2860]: Registering new address record for 10.0.0.70 on eth1. Jan 30 23:57:10 snomONE avahi-daemon[2860]: Registering HINFO record with values 'I686'/'LINUX'. Jan 30 23:57:10 snomONE PBX[2873]: PBX: Starting up Jan 30 23:57:11 snomONE avahi-daemon[2860]: Server startup complete. Host name is snomONE.local. Local service cookie is 472793016. Jan 30 23:57:57 snomONE PBX[2874]: PBX: Administrator logged in from 10.0.0.40 (session=ix4kkspufjr5w30gmyq0) Jan 30 23:58:41 snomONE netborder: /opt/Netborder/Express/Gateway/config/pstn-config.xml:2: element pstnConfig: Relax-NG validity error : Element pstnConfig failed to validate attributes Jan 30 23:58:41 snomONE netborder: /opt/Netborder/Express/Gateway/config/pstn-config.xml:165: element boards: Relax-NG validity error : Expecting an element , got nothing Jan 30 23:58:41 snomONE netborder: XML validation against schema failed on /opt/Netborder/Express/Gateway/config/pstn-config.xml Jan 30 23:58:41 snomONE netborder: /opt/Netborder/Express/Gateway/config/pstn-config.xml:2: element pstnConfig: Relax-NG validity error : Element pstnConfig failed to validate attributes Jan 30 23:58:41 snomONE netborder: /opt/Netborder/Express/Gateway/config/pstn-config.xml:165: element boards: Relax-NG validity error : Expecting an element , got nothing Jan 30 23:58:41 snomONE netborder: XML validation against schema failed on /opt/Netborder/Express/Gateway/config/pstn-config.xml
×
×
  • Create New...