positive

Thank You Matt ! I finally mixed configuration files (comming from 3CX conf) and it works fine now ! here it is : - Replace PATTON_IP and SNOM_ONE_IP.. - PATTON SIDE : no use of WAN and S0 - SNOM_ONE side : I put the option "RINGBACK : MESSAGE 180" in the trunks #----------------------------------------------------------------# # # # SN4552/2BIS/EUI # # R5.3 2009-09-14 SIP # # 2011-07-20T12:11:45 # # SN/00A0BA028A7F # # Generated configuration file # # # #----------------------------------------------------------------# cli version 3.20 clock local offset +02:00 webserver port 80 language en sntp-client sntp-client server primary 79.120.83.33 port 123 version 4 system ic voice 0 profile ppp default profile call-progress-tone defaultDialtone play 1 1000 440 0 profile call-progress-tone defaultAlertingtone play 1 1500 440 -7 pause 2 3500 profile call-progress-tone defaultBusytone play 1 500 440 -7 pause 2 500 profile tone-set default profile voip default codec 1 g711alaw64k rx-length 20 tx-length 20 codec 2 g711ulaw64k rx-length 20 tx-length 20 fax transmission 1 relay t38-udp profile pstn default profile sip default profile aaa default method 1 local method 2 none context ip router interface IF_IP_WAN ipaddress dhcp tcp adjust-mss rx mtu tcp adjust-mss tx mtu interface IF_IP_LAN ipaddress PATTON_IP 255.255.255.0 tcp adjust-mss rx mtu tcp adjust-mss tx mtu context cs switch national-prefix 0 routing-table called-e164 RT_ISDN_TO_SIP_0 route T2 dest-interface IF_SIP_0 MAPPING_INCOMING_CALLS mapping-table calling-pi to calling-e164 MAP_REMOVE_BLANK_CALLERID map restricted to "" mapping-table calling-e164 to calling-e164 MAP_LEADING_ZERO map (.%)-(.%)-(.%)-(.%)-(.%) to \1\2\3\4\5 map (.%)-(.%)-(.%)-(.%) to \1\2\3\4 map (.%)-(.%)-(.%) to \1\2\3 map (.%)-(.%) to \1\2 mapping-table calling-e164 to calling-name MAP_CID_TO_CNAME map (.%) to \1 complex-function MAPPING_INCOMING_CALLS execute 1 MAP_REMOVE_BLANK_CALLERID execute 2 MAP_LEADING_ZERO interface isdn IF_ISDN_0 route call dest-table RT_ISDN_TO_SIP_0 call-hold disable caller-name user-side-ringback-tone interface sip IF_SIP_0 bind context sip-gateway GW_SIP_0 route call dest-interface IF_ISDN_0 remote SNOM_ONE_IP early-connect early-disconnect address-translation outgoing-call request-uri user-part fix 10001 host-part to-header target-param none context cs switch no shutdown authentication-service AS_ALL_LINES realm 1 3CXPhoneSystem username 10001 password XXXXXXXXXXXXXXXXX== encrypted location-service LS_10001 domain 1 SNOM_ONE_IP identity-group default authentication outbound authenticate 1 authentication-service AS_ALL_LINES username 10001 identity 10001 authentication outbound authenticate 1 authentication-service AS_ALL_LINES registration outbound registrar SNOM_ONE_IP 5062 lifetime 300 register auto context sip-gateway GW_SIP_0 interface LAN bind interface IF_IP_LAN context router port 5062 context sip-gateway GW_SIP_0 bind location-service LS_10001 no shutdown port ethernet 0 0 encapsulation ip bind interface IF_IP_WAN router no shutdown port ethernet 0 1 encapsulation ip bind interface IF_IP_LAN router no shutdown port bri 0 0 clock auto encapsulation q921 q921 protocol pp uni-side auto encapsulation q931 q931 protocol dss1 uni-side user bchan-number-order ascending encapsulation cc-isdn bind interface IF_ISDN_0 switch port bri 0 0 no shutdown port bri 0 1 clock auto encapsulation q921 q921 uni-side auto encapsulation q931 q931 protocol dss1 uni-side net bchan-number-order ascending port bri 0 1 shutdown #-------------- END ------------------

Hello, It's better now ! I found myself how to get the calls from the isdn to redirect them to the snom one but I have 2 problems : the incomming call rings 1 time and is lost (if I take the phone before, the communication is OK..) and the number loose its first digit(0).. any idea ? thank you for anyone ! here is the config file Patton 4552 (Hardware Version 2.1, Software Version R5.3) #----------------------------------------------------------------# # # # SN4552/2BIS/EUI # # R5.3 2009-09-14 SIP # # 2011-07-18T19:31:24 # # SN/00A0BA028A7F # # Generated configuration file # # # #----------------------------------------------------------------# cli version 3.20 dns-client server 192.168.0.1 dns-relay webserver port 80 language en sntp-client sntp-client server primary europe.pool.ntp.org port 123 version 4 system ic voice 0 profile ppp default profile tone-set default profile voip default codec 1 g711alaw64k rx-length 20 tx-length 20 codec 2 g729 rx-length 20 tx-length 20 dtmf-relay rtp fax transmission 1 relay t38-udp profile pstn default profile sip default profile aaa default method 1 local method 2 none context ip router interface IF_LAN ipaddress 192.168.0.211 255.255.255.0 tcp adjust-mss rx mtu tcp adjust-mss tx mtu context ip router route 0.0.0.0 0.0.0.0 192.168.0.1 0 context cs switch routing-table called-e164 RT_TO_NETWORK route .T2 dest-service SER_HG_TO_NETWORK routing-table called-e164 RT_TO_PBX route default none route [1-9].% dest-service SER_HG_TO_PBX interface isdn IF_ISDN_00 route call dest-interface IF_SIP_VOIPVOICE interface isdn IF_ISDN_01 route call dest-table RT_TO_NETWORK interface sip IF_SIP_VOIPVOICE bind context sip-gateway GW_SIP route call dest-table RT_TO_PBX remote 192.168.0.240 local 192.168.0.240 privacy service hunt-group SER_HG_TO_NETWORK route call 1 dest-interface IF_SIP_VOIPVOICE route call 2 dest-interface IF_ISDN_00 service hunt-group SER_HG_TO_PBX route call 1 dest-interface IF_ISDN_01 context cs switch no shutdown location-service SER_LOC_VOIPVOICE domain 1 192.168.0.240 context sip-gateway GW_SIP interface IF_LAN bind interface IF_LAN context router port 5062 context sip-gateway GW_SIP bind location-service SER_LOC_VOIPVOICE no shutdown port ethernet 0 0 encapsulation ip no shutdown port ethernet 0 1 encapsulation ip bind interface IF_LAN router no shutdown port bri 0 0 clock slave encapsulation q921 q921 permanent-layer2 uni-side user encapsulation q931 q931 protocol dss1 uni-side user bchan-number-order ascending encapsulation cc-isdn bind interface IF_ISDN_00 switch port bri 0 0 no shutdown port bri 0 1 clock auto encapsulation q921 q921 permanent-layer2 protocol pp uni-side net encapsulation q931 q931 protocol dss1 uni-side net bchan-number-order ascending encapsulation cc-isdn bind interface IF_ISDN_01 switch port bri 0 1 no shutdown #---------------- END ---------------------------------

Hello, I'm a newbee with Patton 4552 ISDN Gateway. I tried to configure a Patton 4552 (R5.3) but without success.. I tried an xls file (SN_VoipVoice_Configuration_Tool.xls provided by Patton) to make a configuration file but this is not the result I need. I use this Gateway to connect an ISDN line (T0) to a SNOM ONE, I already have a modem/router on the network and I use the Snom One SIP Trunk for outgoing calls.(so I don't use WAN or ETH0/0 connector on the Gateway). I need to redirect all the incoming calls to the Snom ONE. I have another trunk "PATTON GW" on the Snom ONE (inbound & outbound) and I need the numbers beginning with '1' to go to that Gateway and the ISDN network. I need also to connect an ISDN phone to Phone connector (BRI0/1) in case the SIP trunk or the Snom One is down.. Thank you for helping me! Regards Patrick

Hello, I want to begin with Snom One and I'd like to know what gateway can I use to connect PSTN and ISDN.. (one or two gateways at the same time) Thank you