lirees

What do you mean by "If no CNG tone, it lets it flow through" ??? I know the fax numbers that the PBX does not manage ... in theory, as well as in DID the pbx forward the call to a specific extension, i must to configure the PBX when on a incoming call on this number does not do anything ... but how can I do ?? thank

Hi, i have a isdn line with 3 numbers connected with snom one through the patton 4554, but only one of those numbers is the voice number the other is connect to a fax machines, how can do to set up the pbx for not answer when a incoming call on the number of fax thanks

I thought about this, but the office hours is every day different, the only solution is to activate a manual service flag when the office is closed I sow that in menu account under redirection i can specify the time when system calls the cell phone and associate it with the activation of the specific service flag .... this could solve everything ... but i would like to specify the times when the cell phone is available outside the office hours the best solution is use the star code *00xx directly in the hunt grup but this solution don't work thanks

excuse me, but I have not explained properly during the office hours i wish that ring only the extensions of the hunt group and not the cell phone ( and for this there is no problem ) ... outside the office hours i activate the service flag and i wish that ring also the cell phone of the extensions at the same time thanks

Hello everyone it's possible to call two o more cell phones of the extensions at the same time by a ring group ? i tried to insert *00ext1 *00ext2 *00ext3 in the "Stage 1 Extensions" of the hunt group but the phone give me a busy signal, then i tried to insert directly the cell phone number in the "Stage 1 Extensions" of the hunt grup but the first number is called

the support patton give me all the information to configure the SmartNode 4554 In this configuration file each bri is connected to snom One with a separate trunk, the bri0 on the port 5060 an the bri1 on the port 5062. (attencion ...enabled the snom One to listen on port 5062 and restart the PBX) Create 2 trunk and configure only the proxy address and the domain : ip-patton:5060 for the first trunk and ip-patton:5062 for the second trunk ... anything else this is the configuration file, i tested it with the firmware 5.5 and 5.6 without problem ****************************************************************** cli version 3.20 clock local default-offset +00:00 webserver port 80 language en system ic voice 0 system clock-source 1 bri 0 0 clock-source 2 bri 0 1 profile ppp default profile call-progress-tone defaultDialtone pause 1 1000 pause 2 200 profile call-progress-tone defaultBusytone play 1 200 425 -7 pause 2 200 profile tone-set default profile voip default codec 1 g711alaw64k rx-length 20 tx-length 20 codec 2 g711ulaw64k rx-length 20 tx-length 20 codec 3 g729 rx-length 20 tx-length 20 fax transmission 1 relay t38-udp profile pstn default profile sip default no autonomous-transitioning profile aaa default method 1 local method 2 none context ip router interface IF_IP_LAN ipaddress >>>IP-PATTON<<< 255.255.255.0 tcp adjust-mss rx mtu tcp adjust-mss tx mtu context cs switch routing-table called-e164 RT_ISDN_TO_SIP_0 route .T2 dest-interface IF_SIP_0 map_add_0 routing-table called-e164 RT_ISDN_TO_SIP_1 route .T2 dest-interface IF_SIP_1 map_add_0 routing-table called-e164 rt_ip_to_isdn mapping-table called-e164 to called-e164 map_add_0 map (.%) to 0\1 interface isdn IF_ISDN_0 route call dest-table RT_ISDN_TO_SIP_0 call-hold disable caller-name user-side-ringback-tone interface isdn IF_ISDN_1 route call dest-table RT_ISDN_TO_SIP_1 call-hold disable caller-name user-side-ringback-tone interface sip IF_SIP_0 bind context sip-gateway GW_SIP_0 route call dest-interface IF_ISDN_0 remote >>>IP-SNOMONE<<< 5060 local >>>IP-SNOMONE<<< 5060 early-connect early-disconnect address-translation outgoing-call request-uri user-part host-part to-header target-param none interface sip IF_SIP_1 bind context sip-gateway GW_SIP_1 route call dest-interface IF_ISDN_1 remote >>>IP-SNOMONE<<< 5062 local >>>IP-SNOMONE<<< 5062 early-connect early-disconnect address-translation outgoing-call request-uri user-part host-part to-header target-param none context cs switch no shutdown context sip-gateway GW_SIP_0 interface LAN bind interface IF_IP_LAN context router port 5060 context sip-gateway GW_SIP_0 no shutdown context sip-gateway GW_SIP_1 interface LAN bind interface IF_IP_LAN context router port 5062 context sip-gateway GW_SIP_1 no shutdown port ethernet 0 0 encapsulation ip bind interface IF_IP_LAN router no shutdown port bri 0 0 clock auto encapsulation q921 q921 protocol pp uni-side auto encapsulation q931 q931 protocol dss1 uni-side user bchan-number-order ascending encapsulation cc-isdn bind interface IF_ISDN_0 switch port bri 0 0 no shutdown port bri 0 1 clock auto encapsulation q921 q921 protocol pp uni-side auto encapsulation q931 q931 protocol dss1 uni-side user bchan-number-order ascending encapsulation cc-isdn bind interface IF_ISDN_1 switch port bri 0 1 no shutdown ******************************************************************

I try to contact the patton support now

I know this gateway configuration tools, it is very nice but only works with the PSTN device .. I try to find a gateway configuration tools for the patton bri but i found nothing

Hello everyone I am trying to configure the patton 4554 with firmware 5.6 without any result ... I tried to import the configuration file generated by the patton 3cx but the patton do not register! Where can I find a template configuration for firmware 5.6 and the snom one? thanks