lirees
-
Posts
34 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by lirees
-
-
Hi,
i have a isdn line with 3 numbers connected with snom one through the patton 4554, but only one of those numbers is the voice number the other is connect to a fax machines, how can do to set up the pbx for not answer when a incoming call on the number of fax
thanks
-
Instead of using the service flag on the hunt group you can make use of "Specify time when system calls the cell phone" on the extension's redirection page. But again you have to remember that this will make the cell phone ringing only during the time you have specified for all calls(not just for the hunt group calls)
I thought about this, but the office hours is every day different, the only solution is to activate a manual service flag when the office is closed
I sow that in menu account under redirection i can specify the time when system calls the cell phone and associate it with the activation of the specific service flag .... this could solve everything ... but i would like to specify the times when the cell phone is available outside the office hours
the best solution is use the star code *00xx directly in the hunt grup but this solution don't work
thanks
-
excuse me, but I have not explained properly
during the office hours i wish that ring only the extensions of the hunt group and not the cell phone ( and for this there is no problem ) ... outside the office hours i activate the service flag and i wish that ring also the cell phone of the extensions at the same time
thanks
-
Hello everyone
it's possible to call two o more cell phones of the extensions at the same time by a ring group ?
i tried to insert *00ext1 *00ext2 *00ext3 in the "Stage 1 Extensions" of the hunt group but the phone give me a busy signal, then i tried to insert directly the cell phone number in the "Stage 1 Extensions" of the hunt grup but the first number is called
-
the support patton give me all the information to configure the SmartNode 4554
In this configuration file each bri is connected to snom One with a separate trunk, the bri0 on the port 5060 an the bri1 on the port 5062. (attencion ...enabled the snom One to listen on port 5062 and restart the PBX)
Create 2 trunk and configure only the proxy address and the domain : ip-patton:5060 for the first trunk and ip-patton:5062 for the second trunk ... anything else
this is the configuration file, i tested it with the firmware 5.5 and 5.6 without problem
******************************************************************
cli version 3.20
clock local default-offset +00:00
webserver port 80 language en
system
ic voice 0
system
clock-source 1 bri 0 0
clock-source 2 bri 0 1
profile ppp default
profile call-progress-tone defaultDialtone
pause 1 1000
pause 2 200
profile call-progress-tone defaultBusytone
play 1 200 425 -7
pause 2 200
profile tone-set default
profile voip default
codec 1 g711alaw64k rx-length 20 tx-length 20
codec 2 g711ulaw64k rx-length 20 tx-length 20
codec 3 g729 rx-length 20 tx-length 20
fax transmission 1 relay t38-udp
profile pstn default
profile sip default
no autonomous-transitioning
profile aaa default
method 1 local
method 2 none
context ip router
interface IF_IP_LAN
ipaddress >>>IP-PATTON<<< 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
context cs switch
routing-table called-e164 RT_ISDN_TO_SIP_0
route .T2 dest-interface IF_SIP_0 map_add_0
routing-table called-e164 RT_ISDN_TO_SIP_1
route .T2 dest-interface IF_SIP_1 map_add_0
routing-table called-e164 rt_ip_to_isdn
mapping-table called-e164 to called-e164 map_add_0
map (.%) to 0\1
interface isdn IF_ISDN_0
route call dest-table RT_ISDN_TO_SIP_0
call-hold disable
caller-name
user-side-ringback-tone
interface isdn IF_ISDN_1
route call dest-table RT_ISDN_TO_SIP_1
call-hold disable
caller-name
user-side-ringback-tone
interface sip IF_SIP_0
bind context sip-gateway GW_SIP_0
route call dest-interface IF_ISDN_0
remote >>>IP-SNOMONE<<< 5060
local >>>IP-SNOMONE<<< 5060
early-connect
early-disconnect
address-translation outgoing-call request-uri user-part host-part to-header target-param none
interface sip IF_SIP_1
bind context sip-gateway GW_SIP_1
route call dest-interface IF_ISDN_1
remote >>>IP-SNOMONE<<< 5062
local >>>IP-SNOMONE<<< 5062
early-connect
early-disconnect
address-translation outgoing-call request-uri user-part host-part to-header target-param none
context cs switch
no shutdown
context sip-gateway GW_SIP_0
interface LAN
bind interface IF_IP_LAN context router port 5060
context sip-gateway GW_SIP_0
no shutdown
context sip-gateway GW_SIP_1
interface LAN
bind interface IF_IP_LAN context router port 5062
context sip-gateway GW_SIP_1
no shutdown
port ethernet 0 0
encapsulation ip
bind interface IF_IP_LAN router
no shutdown
port bri 0 0
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_0 switch
port bri 0 0
no shutdown
port bri 0 1
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_1 switch
port bri 0 1
no shutdown
******************************************************************
-
I'm very interested in solving the BRI/PRI/ config issue too.
Did you talk to Patton?
If not i will talk to Patton and see if I can get us a solution to patton pri/bri/etc gateways.
Matt
I try to contact the patton support now
-
oh,i see that is a bri. i haven't used this config tool for BRI yet myself.
I've used it for the patton 4300 soo far and it worked brilliantly.
I solicit feedback on this tool
matt
I know this gateway configuration tools, it is very nice but only works with the PSTN device .. I try to find a gateway configuration tools for the patton bri but i found nothing
-
Hello everyone
I am trying to configure the patton 4554 with firmware 5.6 without any result ... I tried to import the configuration file generated by the patton 3cx but the patton do not register!
Where can I find a template configuration for firmware 5.6 and the snom one?
thanks
incoming call on the fax numbers
in General Setup
Posted
What do you mean by "If no CNG tone, it lets it flow through" ???
I know the fax numbers that the PBX does not manage ... in theory, as well as in DID the pbx forward the call to a specific extension, i must to configure the PBX when on a incoming call on this number does not do anything ... but how can I do ??
thank