Hampden Solutions Posted July 19, 2012 Report Posted July 19, 2012 Hi All have a problem with snom one version 4.5 and a Patton 4112 incoming calls work fine, but get an off hook sound when trying to dial out PAtton COnfig is below, can you confirm this is ok------------------------------------------------------------------------------ RUNNING CONFIGURATION ===================== #----------------------------------------------------------------# # # # SN4112/JO/EUI # # R5.2 2009-01-14 H323 SIP FXS FXO # # 1970-01-01T01:47:58 # # SN/00A0BA0763CC # # Generated configuration file # # # #----------------------------------------------------------------# cli version 3.20 webserver port 80 language en sntp-client sntp-client server primary 194.35.252.7 port 123 version 4 sntp-client server secondary 194.164.127.5 port 123 version 4 sntp-client local-clock-offset system ic voice 0 low-bitrate-codec g729 profile ppp default profile call-progress-tone defaultDialtone play 1 1000 450 -6 profile call-progress-tone defaultAlertingtone play 1 1000 450 -13 pause 2 5000 profile call-progress-tone defaultBusytone play 1 300 450 -7 pause 2 300 profile call-progress-tone defaultReleasetone play 1 300 450 -7 pause 2 300 profile call-progress-tone defaultCongestiontone play 1 300 450 -7 pause 2 300 profile tone-set default profile voip default codec 1 g711alaw64k rx-length 20 tx-length 20 codec 2 g711ulaw64k rx-length 20 tx-length 20 fax transmission 1 relay t38-udp fax transmission 2 bypass g711alaw64k profile pstn default profile sip default profile aaa default method 1 local method 2 none context ip router interface IF_IP_LAN ipaddress dhcp tcp adjust-mss rx mtu tcp adjust-mss tx mtu interface IF_IP_WAN ipaddress dhcp tcp adjust-mss rx mtu tcp adjust-mss tx mtu context cs switch digit-collection timeout 2 interface sip IF_SIP_1 bind context sip-gateway GW_SIP_ALL_LINES route call dest-service HUNT_FXO remote 10.0.2.15 5060 early-connect early-disconnect address-translation outgoing-call request-uri user-part fix 10015 host-part to-header target-param none interface sip IF_SIP_2 bind context sip-gateway GW_SIP_ALL_LINES route call dest-service HUNT_FXO remote 10.0.2.15 5060 early-connect early-disconnect address-translation outgoing-call request-uri user-part fix 10016 host-part to-header target-param none interface fxo IF_FXO_1 route call dest-interface IF_SIP_1 loop-break-duration min 60 max 5000 disconnect-signal loop-break disconnect-signal busy-tone ring-number on-caller-id dial-after timeout 1 mute-dialing interface fxo IF_FXO_2 route call dest-interface IF_SIP_2 loop-break-duration min 100 max 500 disconnect-signal loop-break disconnect-signal busy-tone ring-number on-caller-id dial-after timeout 1 mute-dialing service hunt-group HUNT_FXO cyclic drop-cause normal-unspecified drop-cause no-circuit-channel-available drop-cause network-out-of-order drop-cause temporary-failure drop-cause switching-equipment-congestion drop-cause access-info-discarded drop-cause circuit-channel-not-available drop-cause resources-unavailable route call 1 dest-interface IF_FXO_1 route call 2 dest-interface IF_FXO_2 context cs switch no shutdown authentication-service AS_ALL_LINES username test password 3X2zrM+s3Z0= encrypted location-service LS_ALL_LINES identity 10015 identity 10016 context sip-gateway GW_SIP_ALL_LINES interface LAN bind interface IF_IP_LAN context router port 5060 context sip-gateway GW_SIP_ALL_LINES no shutdown port ethernet 0 0 medium auto encapsulation ip bind interface IF_IP_LAN router no shutdown port fxo 0 0 use profile fxo gb encapsulation cc-fxo bind interface IF_FXO_1 switch no shutdown port fxo 0 1 use profile fxo gb encapsulation cc-fxo bind interface IF_FXO_2 switch no shutdown ============================================================================== Quote
Guest kevin Posted July 23, 2012 Report Posted July 23, 2012 From looking at the SIP trace are we sending the invite to the Patton? If we are and it looks good i.e. the from and the field are proper then I would contact Patton for some help. They have good support from what I was told. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.