Alex Sergeev

Good day! Tell me please, how to configure the dial plan so that I could dial a literal expression? For example, from phone dial name@skype.sipnet.ru and call goes to a specific trunk.

I did not understand what you mean. At PBXnSIP, we use the same domain. But I do not understand why we need to append the name "localhost". On the Domains tab, I see a warning: You have only one domain, but that domain does not include the name "localhost". This might cause problems match incoming requests with the domain. Consider adding the name "localhost" to the list of domain names of your domain. You believe that the solution to our problem lies in that phrase? P.S. I recall that we have a problem with global address book PBXnSIP. LDAP, we do not use.

1. Are you sure you are running .3981? (check the status page) Yes, I'm sure 4.2.0.3981 (Linux) on CentOS 5.4. 2. Are you sure if the phone has done the PnP with the PBX that is running .3981? Sometimes, folks have done PnP with different PBX (running older version) and configured an identity to the new PBX. I tried to connect "new" phone to the PBXnSIP. The problem remains. And can PnP xml-files of old versions inherit to new version PBXnSIP after upgrade? 3. The 1000 entries could be a problem, especially if the PBX has to perform a table scan. What you can do is run taskmgr, put it on fast update then hit the directory key a couple of times and see if one of the cores goes to 100 % load. On version 4.0.1.3499 with 1000 entries the problems was not. But I tried to measure CPU load. The pbxctrl process does not exceed 5% during the request to the address book. Also, I took a tshark-dump. Maybe you have something in it to see? DirectorySlow.zip

Dear Colleagues, Anybody can help me understand my problem?

At present we have 50 extensions. About 1000 entries in domain address book. P.S. After upgrade from 4.0.1.3499 to 4.2.0.3981, not all phones have been reset. Although over 5 second delay on all phones (reseting or not).

Good day! After upgrade from 4.0.1.3499 to 4.2.0.3981 when I press the Directory key on any snom phone, I need to wait more than 5 seconds to display a list of contacts. If I press the letter key, I must also wait more than 5 seconds. And so on. It is very inconvenient. Until that time, much faster. Help my users please.

Thank you! Firmware update solved the problem.

Hello! Sorry for my English. We have a problem with provisioning Button type "Monitoring extension (on phone)" on function keys. The experiment itself: • An extension 2067 (Snom 300 IP 172.16.96.66) makes a call to an extension 2139 (Snom 320 IP 172.16.96.200). • Extension 2139 is not responding. • At this time, the extension 2084 (Snom 320 IP 172.16.96.31), who programmed the seventh function key “Monitoring extension (on phone)” with parameter 2139, noted that the seventh key blinks, and tries to pickup a call by pressing 7. • On phone display caller 2084 shows: * 60122. Caller 2067 loses call, hearing the busy tone. Call to the number in 2139 continues to go on the screen still displays the caller's name in 2067 and in response to this call to connect subscribers in 2084 and 2139 (I would like to 2084 to 2067). For extension 2084 set Watch the calls of the following extensions and Watch the presence of the following extensions with parameters 2139. For Extension 2139 set Dialog Permissions with parameters 2084. PBXnSIP v.4.0.1.3499. Caller phones - Snoms 320 v.8.4.18. Please help. P.S. If necessary, I can provide cap-files from phones and PBXnSIP.

Good day! Sorry for my English. Please help me configure automatic time synchronization on the server CentOS where installed PBXnSIP. I tried to manually synchronize the time: ntpdate 172.16.99.1 but a message appears: the NTP socket is in use, exiting I found out that port 123 works pbxctrl. I stopped the service pbxnsip. After that I was able to manually synchronize the time. What are the steps you must follow to set up automatic synchronization?

Thanks for your reply! In Accounts > Extension > Buttons, who are appointed, automatic provision on Snom 300 without problem. But in this section is not possible to specify the URL. Why In Admin> Settings> PnP section does not work automatic provisioning the Snom 300 buttons? I think what you are talking about xml-provision files. How this xml-file to find? And where to put if I have RedHat Linux Platform?

Sorry for my english, I'm from Russia. In Admin > Settings > PnP Setting for snom 300 (button 4): is url {http-url snom}/adrbook.xml?user={id}&auth={webhash}. But none of Snoms 300 is not receiving the setting button. With that, I tried to input other key event to this button in Admin > Settings > PnP Setting for snom 300 (button 4). And I came to the conclusion that the Snoms 300 do not receive the settings buttons from PBXnSIP. Version of PBXnSIP - 4.0.1.3499 (RedHat Linux). Firmware of Snom 300 - 8.2.35. Thank!

Thank you! This pattern work. Where I can read about regular expressions, wich function in PBXnSIP?

Please, help me. Sorry for my english. Recently our company buyed PBXnSIP 3.0. I have problem with some patterns. For example, I need write pattern for range 9150000000-9154999999. I think that pattern (915[0-4]*) will right. But this rule send only first four digits on trunk. Help me to write pattern for this range 9150000000-9154999999. And when I may to read about pattern syntax? Thanks.