Jump to content

config patton 4554 firmware 5.6


lirees
 Share

Recommended Posts

Hello everyone

I am trying to configure the patton 4554 with firmware 5.6 without any result ... I tried to import the configuration file generated by the patton 3cx but the patton do not register!

Where can I find a template configuration for firmware 5.6 and the snom one?

 

thanks

Link to comment
Share on other sites

oh,i see that is a bri. i haven't used this config tool for BRI yet myself.

I've used it for the patton 4300 soo far and it worked brilliantly.

 

I solicit feedback on this tool

matt

 

I know this gateway configuration tools, it is very nice but only works with the PSTN device .. I try to find a gateway configuration tools for the patton bri but i found nothing

Link to comment
Share on other sites

the support patton give me all the information to configure the SmartNode 4554

In this configuration file each bri is connected to snom One with a separate trunk, the bri0 on the port 5060 an the bri1 on the port 5062. (attencion ...enabled the snom One to listen on port 5062 and restart the PBX)

Create 2 trunk and configure only the proxy address and the domain : ip-patton:5060 for the first trunk and ip-patton:5062 for the second trunk ... anything else

 

this is the configuration file, i tested it with the firmware 5.5 and 5.6 without problem

 

******************************************************************

cli version 3.20

clock local default-offset +00:00

webserver port 80 language en

 

system

 

ic voice 0

 

system

clock-source 1 bri 0 0

clock-source 2 bri 0 1

 

profile ppp default

 

profile call-progress-tone defaultDialtone

pause 1 1000

pause 2 200

 

profile call-progress-tone defaultBusytone

play 1 200 425 -7

pause 2 200

 

profile tone-set default

 

profile voip default

codec 1 g711alaw64k rx-length 20 tx-length 20

codec 2 g711ulaw64k rx-length 20 tx-length 20

codec 3 g729 rx-length 20 tx-length 20

fax transmission 1 relay t38-udp

 

profile pstn default

 

profile sip default

no autonomous-transitioning

 

profile aaa default

method 1 local

method 2 none

 

context ip router

 

interface IF_IP_LAN

ipaddress >>>IP-PATTON<<< 255.255.255.0

tcp adjust-mss rx mtu

tcp adjust-mss tx mtu

 

context cs switch

 

routing-table called-e164 RT_ISDN_TO_SIP_0

route .T2 dest-interface IF_SIP_0 map_add_0

 

routing-table called-e164 RT_ISDN_TO_SIP_1

route .T2 dest-interface IF_SIP_1 map_add_0

 

routing-table called-e164 rt_ip_to_isdn

 

mapping-table called-e164 to called-e164 map_add_0

map (.%) to 0\1

 

interface isdn IF_ISDN_0

route call dest-table RT_ISDN_TO_SIP_0

call-hold disable

caller-name

user-side-ringback-tone

 

interface isdn IF_ISDN_1

route call dest-table RT_ISDN_TO_SIP_1

call-hold disable

caller-name

user-side-ringback-tone

 

interface sip IF_SIP_0

bind context sip-gateway GW_SIP_0

route call dest-interface IF_ISDN_0

remote >>>IP-SNOMONE<<< 5060

local >>>IP-SNOMONE<<< 5060

early-connect

early-disconnect

address-translation outgoing-call request-uri user-part host-part to-header target-param none

 

interface sip IF_SIP_1

bind context sip-gateway GW_SIP_1

route call dest-interface IF_ISDN_1

remote >>>IP-SNOMONE<<< 5062

local >>>IP-SNOMONE<<< 5062

early-connect

early-disconnect

address-translation outgoing-call request-uri user-part host-part to-header target-param none

 

context cs switch

no shutdown

 

context sip-gateway GW_SIP_0

 

interface LAN

bind interface IF_IP_LAN context router port 5060

 

context sip-gateway GW_SIP_0

no shutdown

 

context sip-gateway GW_SIP_1

 

interface LAN

bind interface IF_IP_LAN context router port 5062

 

context sip-gateway GW_SIP_1

no shutdown

 

port ethernet 0 0

encapsulation ip

bind interface IF_IP_LAN router

no shutdown

 

port bri 0 0

clock auto

encapsulation q921

 

q921

protocol pp

uni-side auto

encapsulation q931

 

q931

protocol dss1

uni-side user

bchan-number-order ascending

encapsulation cc-isdn

bind interface IF_ISDN_0 switch

 

port bri 0 0

no shutdown

 

port bri 0 1

clock auto

encapsulation q921

 

q921

protocol pp

uni-side auto

encapsulation q931

 

q931

protocol dss1

uni-side user

bchan-number-order ascending

encapsulation cc-isdn

bind interface IF_ISDN_1 switch

 

port bri 0 1

no shutdown

******************************************************************

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...