TPaulat Posted August 29, 2011 Report Share Posted August 29, 2011 I´m a newbie to snomONE, came over from Mitel System. For a customer project I´ve configured a snomOne PBx and I´m absolutly thrilled about the system. My problem points out here: I´m not familiar to the Patton SN 4554. Also trying to configure the Patton with the Configuration Tool (June 2011) bring´s not much effect. Searching for guides etc brought not much effect. Need to know how to set up connection between snomONE and Patton GW (SIP GW? SIP Registration? etc.). System information EuroISDN PP 2x S0 Snom One IP 192.168.168.245/24 DNS IP 192.168.168.250/24 Gateway IP 192.168.168.254/24 Patton IP 192.168.168.246/24 Created this configuration file with the tool: #################################################################################### # Configuration file for SmartNode with: 0 FXO and 0 FXS # With one ethernet port # Configuration file name is tretwerk # Snome One IPPBX #################################################################################### # LAN Interface Data # IP Address 192.168.168.246 # IP Mask 255.255.255.0 #################################################################################### # WAN Interface Data # IP Address dhcp # IP Mask #################################################################################### # Default Gateway 192.168.168.254 #################################################################################### # IP-PBX/SIP PROXY DATA # IP-PBX Ip Address / Name / Domain 192.168.168.245 # IP-PBX SIP Port 5060 #################################################################################### # LOCALIZATION DATA # Country Germany #################################################################################### # Supported firmware versions R5.x # Tool version V2_1 06222011 # Adapted: Ernesto Casas # for comments, feedback or suggestions please send an email to: ecasas@patton.com #################################################################################### #################################################################################### webserver port 80 language en sntp-client server 192.53.103.108 dns-client server 192.168.168.250 system ic voice 0 low-bitrate-codec g729 profile ppp default # Call Progress tones based on country selection. Your selected country is: Germany profile call-progress-tone defaultDialtone flush-play-list play 1 1000 425 0 profile call-progress-tone defaultAlertingtone flush-play-list play 1 1000 425 -7 pause 2 4000 profile call-progress-tone defaultBusytone flush-play-list play 1 480 425 -7 pause 2 480 profile call-progress-tone defaultReleasetone flush-play-list play 1 240 425 -7 pause 2 240 profile call-progress-tone defaultCongestiontone flush-play-list play 1 240 425 -7 pause 2 240 profile tone-set default profile voip default codec 1 g711alaw64k rx-length 20 tx-length 20 codec 2 g711ulaw64k rx-length 20 tx-length 20 fax transmission 1 relay t38-udp fax transmission 2 bypass g711alaw64k profile pstn default profile sip default profile aaa default method 1 local method 2 none context ip router interface IF_IP_LAN ipaddress 192.168.168.246 255.255.255.0 tcp adjust-mss rx mtu tcp adjust-mss tx mtu interface IF_IP_WAN ipaddress dhcp tcp adjust-mss rx mtu tcp adjust-mss tx mtu context ip router route 0.0.0.0 0.0.0.0 192.168.168.254 context cs switch digit-collection timeout 2 service hunt-group HUNT_FXO cyclic drop-cause normal-unspecified drop-cause no-circuit-channel-available drop-cause network-out-of-order drop-cause temporary-failure drop-cause switching-equipment-congestion drop-cause access-info-discarded drop-cause circuit-channel-not-available drop-cause resources-unavailable context cs switch no shutdown context sip-gateway GW_SIP_ALL_LINES interface LAN bind interface IF_IP_LAN context router port 5060 context sip-gateway GW_SIP_ALL_LINES no shutdown port ethernet 0 0 medium auto encapsulation ip bind interface IF_IP_LAN router no shutdown ################################################# END ################################################## ######### Need to know how to set up the connection between snomONE and Patton and If the configuration is ok or If there are mistakes included. How to setup the connection to the PBx, where to create the accounts to log in? Thanks to all for help Quote Link to comment Share on other sites More sharing options...
mattlandis Posted August 29, 2011 Report Share Posted August 29, 2011 your best bet might be to work with patton support. they are excellent in the USA. support@patton.com or call them on published number. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.