Fxo registration dialing out

[mbates]

I have my Audiocodes 114 fxo registered to pbxnsip with extention 100. I was wondering how I dialout from that extention. I see options for "call extention" in my dial plan. But I don't know what patern and replacement to put in there. I want everything to go out my fxo port. I was thinking you put * for the pattern and 100 for the replacement. But it trys to dial 100 instead of the number. Any Ideas.

[Vodia PBX]

I have my Audiocodes 114 fxo registered to pbxnsip with extention 100. I was wondering how I dialout from that extention. I see options for "call extention" in my dial plan. But I don't know what patern and replacement to put in there. I want everything to go out my fxo port. I was thinking you put * for the pattern and 100 for the replacement. But it trys to dial 100 instead of the number. Any Ideas.

 

Is there any reason why you want to register the FXO? Usually you just use the outbound proxy on both the PBX and the gateway to point to each other and use a trunk.

 

If you want to use the "call extension" feature, the replacement is the extension number (e.g. "100", no "sip" or domain name before or after that).

[mbates]

The reason we are registering the fxo port is because it is behind a non configurable router that changes ip addresses.

[Vodia PBX]

The reason we are registering the fxo port is because it is behind a non configurable router that changes ip addresses.

 

Yea, that's the reason why we introduced that "call extension" feature...

[mbates]

Whenever I user * for the pattern and 100 as the replacement. It trys to dial 100 instead of the dialed number. Is there any workaround for this.

[Vodia PBX]

Whenever I user * for the pattern and 100 as the replacement. It trys to dial 100 instead of the dialed number. Is there any workaround for this.

 

Well, what header are you looking at? The Request-URI must be 100, because that's what has been registered.

 

The To-Header should contain the destination number that the gateway should dial.

[brandywinetech.com]

as long as the pbx shows the registration for extension 100 in the accounts section , it will follow whatever dial plan you assign that extension ,

 

just * with no replacement will work , I have setup a bunch of these ...

 

if it doesn't work with that , something is not configured correctly .

 

here is a sample ini file

 

 

;**************

;** Ini File **

;**************

 

;Board: MP-114 FXS

;Serial Number: 712095

;Slot Number: 1

;Software Version: 4.80A.014.006

;Board IP Address: 10.0.0.250

;Board Subnet Mask: 255.255.255.0

;Board Default Gateway: 10.0.0.1

;Ram size: 32M Flash size: 8M

;Num DSPs: 1 Num DSP channels: 4

;Profile: NONE

;------------------------------

 

 

[sYSTEM Params]

 

SyslogServerIP = 10.1.1.89

 

[bSP Params]

 

PCMLawSelect = 3

LocalOAMIPAddress = 10.0.0.250

RoutingTableHopsCountColumn = 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

 

[ATM Params]

 

 

[Analog Params]

 

MinFlashHookTime = 100

FXSLoopCharacteristicsFilename = 'MP11x-02-1-FXS_16KHZ.dat'

CallProgressTonesFilename = 'usa_tones_12.dat'

 

[ControlProtocols Params]

 

MGCPDTMFDetectionPoint = 0

 

[MGCP Params]

 

 

[MEGACO Params]

 

EP_Num_0 = 0

EP_Num_1 = 1

EP_Num_2 = 0

EP_Num_3 = 0

EP_Num_4 = 0

 

[sS7 Params]

 

 

[Voice Engine Params]

 

IdlePCMPattern = 85

VoiceVolume = 1

RFC2833PayloadType = 101

 

[WEB Params]

 

LogoWidth = '339'

 

[sIP Params]

 

ENABLECALLERID = 1

MAXDIGITS = 11

REGISTRATIONTIME = 3600

ISPROXYUSED = 1

ISREGISTERNEEDED = 1

GWDEBUGLEVEL = 5

ENABLEEARLYMEDIA = 1

ISUSERPHONE = 0

PROXYNAME = '10.0.0.254'

REGISTRARIP = '10.0.0.254'

SIPGATEWAYNAME = '10.0.0.250'

CNONCE = '0a123bcf'

PASSWORD = '787899'

ISFAXUSED = 1

REGISTRARNAME = '10.0.0.254'

CODERNAME = g711Ulaw64k,20,0,0,0

PREFIX = *,10.0.0.254,*,0,255

TRUNKGROUP = 1-1,20,0

TRUNKGROUP = 2-2,777,0

TRUNKGROUP = 3-3,22,0

TRUNKGROUP = 4-4,21,0

PROXYIP = 10.0.0.254

AUTHENTICATION_0 = 20,#*0000

AUTHENTICATION_1 = 777,#*0000

AUTHENTICATION_2 = 22,#*0000

AUTHENTICATION_3 = 21,#*0000

TXDTMFOPTION = 4

 

[VXML Params]

 

 

[iPsec Params]

 

 

[Audio Staging Params]

 

 

[PSTN-SDH Params]